how to operate electric scissor lift step by step (sj)~
The operation light indicates upper control availability. It glows when both emergency stop buttons on the platform control console and the base control console are pulled out.
• Test Platform Emergency Stop
1.
Result:
• Test Enable Trigger Switch
1. Pull out “ ” emergency stop button.
2.
2.
3.
4.
NOTE
Lowering is not proportional.
5.
WARNING
NOTE
• Test Platform Raising/Lowering
1. Select lift/off/drive switch to “ ” lift position.
2. Activate and hold “ ” enable trigger switch.
3.
• Test Driving
1. Ensure path of intended motion is clear.
2. Activate and hold “ ”enable trigger switch.
3. and then return handle to center position.
Result: Aerial platform should move in forward direction, and then come to a stop.
4. Slowly move controller handle in “ ” reverse direction until aerial platform begins to move, and then return handle to center position.
Result: Aerial platform should move in reverse direction, and then come to a stop.
WARNING
WARNING
1.
2.
3.
4.
5. Return controller to neutral center position to stop. Release “ ” enable trigger switch.
WARNING
3.
4.
NOTE
Lowering is not proportional.
5.
WARNING
NOTE
• Test Platform Raising/Lowering
1. Select lift/off/drive switch to “ ” lift position.
2. Activate and hold “ ” enable trigger switch.
3.
• Test Driving
1. Ensure path of intended motion is clear.
2. Activate and hold “ ”enable trigger switch.
3. and then return handle to center position.
Result: Aerial platform should move in forward direction, and then come to a stop.
4. Slowly move controller handle in “ ” reverse direction until aerial platform begins to move, and then return handle to center position.
Result: Aerial platform should move in reverse direction, and then come to a stop.
WARNING
WARNING
1.
2.
3.
4.
5. Return controller to neutral center position to stop. Release “ ” enable trigger switch.
WARNING
1. Activate platform control console (refer to Section 3.8-3).
2.
3.
4.
NOTE
Steering is not proportional.
2.
3.
4.
NOTE
Steering is not proportional.
• Test Steering
1. Select lift/off/drive switch to “ ” drive position.
2. Activate and hold “ ” enable trigger switch.
3.
1.
2.
3.
4.
5.
6.
WARNING
Ensure that you maintain three points of contact when using the ladder to mount/ dismount platform.
• Test Brakes
WARNING
Brakes will engage instantly when you release the controller handle, causing aerial platform to stop immediately.
1. Ensure path of intended motion is clear.
2. Activate and hold “ ” enable trigger switch.
3. Drive aerial platform “ ” forward and then “ ” backward. Test brake by releasing controller handle.
Result: Aerial platform should come to a stop. If aerial platform pulls to one side while stopping, do not operate aerial platform until brake adjustments have been checked.
4. Drive aerial platform “ ” forward and then “ ” backward. Test brake again by releasing “ ” enable trigger switch only.
Result: Aerial platform should come to an instant and abrupt stop. If aerial platform does not stop immediately, or if aerial platform pulls to one side while stopping, do not operate aerial platform until brake adjustments have been checked.
ملاحظات نهائية
2.4-3 Platform Control Console
1. Ensure base “ ” emergency stop button is pulled out.
2. Select off/platform/base key switch to “ ” platform position.
3. Ensure main power disconnect switch is in “ ” on position.
WARNING
Ensure that you maintain three points of contact when using the ladder to mount/ dismount platform.
4. Use the ladder of aerial platform to access platform.
5. Close the gate.
6. On platform control console, pull out “ ” emergency stop button.
• Test Horn
1. .
Result:
NOTE
سيتم ذكره فى موضوع خاص به
NOTE
If it is necessary to fold the guardrails, refer to Section 3.9 for guardrail folding procedure.
2.
Select inclined drive/level drive switch to “ ” inclined drive (low speed/high torque) position for reduced speed.
3. Cordon-off the pathway which you intend to travel.
4.
5. Turn main power disconnect switch to “ ” off position.
6. Use the ladder of aerial platform to access platform.
If it is necessary to fold the guardrails, refer to Section 3.9 for guardrail folding procedure.
2.
Select inclined drive/level drive switch to “ ” inclined drive (low speed/high torque) position for reduced speed.
3. Cordon-off the pathway which you intend to travel.
4.
5. Turn main power disconnect switch to “ ” off position.
6. Use the ladder of aerial platform to access platform.
WARNING
Ensure that you maintain three points of contact when using the ladder to mount/ dismount platform.
7. Close the gate. On platform control console, push in “ ” emergency stop button.
8.
9.
10. Use the ladder to dismount from platform.
11.
NOTE
For some models, the connection is located beneath an access panel which requires that the scissor
assembly be raised to access it.
12.
13.
14. Use a spotter to guide movement. Ensure the spotter remains at a safe distance.
15.
16. Turn main power disconnect switch to “ ”on position.
17.
18.
19.
20.
Ensure that you maintain three points of contact when using the ladder to mount/ dismount platform.
7. Close the gate. On platform control console, push in “ ” emergency stop button.
8.
9.
10. Use the ladder to dismount from platform.
11.
NOTE
For some models, the connection is located beneath an access panel which requires that the scissor
assembly be raised to access it.
12.
13.
14. Use a spotter to guide movement. Ensure the spotter remains at a safe distance.
15.
16. Turn main power disconnect switch to “ ”on position.
17.
18.
19.
20.
WARNING
21.
22. Once safely through the doorway, push in “ ” emergency stop button and turn main power disconnect switch to “ ” off position.
23.
21.
22. Once safely through the doorway, push in “ ” emergency stop button and turn main power disconnect switch to “ ” off position.
23.
WARNING
Ensure that you maintain three points of contact when using the ladder to mount/ dismount platform.
24.
Ensure that you maintain three points of contact when using the ladder to mount/ dismount platform.
24.
WARNING
25.
2. Ensure
3. Ensure
4. Turn main power disconnect switch to “ ” off position.
WARNING
Ensure that you maintain three points of contact when using the ladder to mount/ dismount platform.
5. .
6.
7.
8. (if equipped). (Refer to Figure 3-13b):
WARNING
Ensure pin C is in place and secured to the Extension Top Rail.
9. in the following order:
Models 32xx
• Entrance
Use tie wrap to secure entrance bar to leftguardrail.
• Right Side
• Left Side
• Extension
Lock extension guardrail into place on the mounting post. Ensure that the detent ball of the pin is all the way through. (Refer to Figure 3-13c)
• Entrance
Use tie wrap to secure entrance bar to leftguardrail.
• Right Side
• Left Side
• Extension
Lock extension guardrail into place on the mounting post. Ensure that the detent ball of the pin is all the way through. (Refer to Figure 3-13c)
Models 46xx
• Right Side
• Left Side
• Entrance
• Extension
Lock extension guardrail into place on the mounting post. Ensure that the detent ball of the pin is all
the way through. (Refer to Figure 3-13c) Locking Pin
Figure 3-13c. All Guardrails Folded Down
1. Ensure aerial platform is on level ground.
2. Ensure extension platform is fully retracted.
3. Ensure Emergency Stop button is depressed.
4. Turn main power disconnect switch to “ ” off position.
2. Ensure extension platform is fully retracted.
3. Ensure Emergency Stop button is depressed.
4. Turn main power disconnect switch to “ ” off position.
WARNING
Any lowered guardrail will create a fall hazard. Use caution when exiting or entering the platform when the guard rails are lowered.
WARNING
The scissor assembly must be fully lowered before raising or lowering the guardrails.
WARNING
Ensure that you maintain three points of contact when using the ladder to mount/ dismount platform.
5. Use the ladder of aerial platform to access platform.
6. . (Refer to Figure 3-13c)
7. Carefully raise each guardrail up and lock into place with locking pins ensuring that the detent ball of each pin is all the way through. (Refer to Figure 3-13a)
8.
WARNING
Before operating this aerial platform, check the guardrail system for loose or missing locking pins. The guardrail system must be upright and all pins must be locked in place. Death or serious injury could result if the guardrail system is not upright or properly locked.
Know and heed all national, state or territorial/provincial and local rules which apply to your loading/unloading of aerial platforms. Only qualified personnel shall operate machinery during loading/unloading.
The transport vehicle must be parked on a level surface and must be secured to prevent rolling while aerial platform is being loaded/unloaded.
3.
4. 5.
WARNING
Do not operate this aerial platform without proper authorization and training. Failure to avoid this hazard could result in death or serious injury. Before operating this aerial platform, perform the
following steps:
1. Visual and daily maintenance inspections (see Section 2.3)
2. Function tests (see Section 2.4)
3. Job site inspection It is the responsibility of the operator to perform a job site inspection and avoid
the following hazardous situations:
• holes or drop-offs
• ditches or soft fills
• floor obstructions, bumps or debris
• overhead obstructions
• electrical cords, hoses and high voltage conductors
• hazardous locations
• inadequate surface support to withstand all load forces imposed by the aerial platform
• wind and weather conditions
• the presence of unauthorized personnel
• other possible unsafe conditions
WARNING
An operator should not use any aerial platform that:
• does not appear to be working properly.
• has been damaged or appears to have worn or missing parts.
• has alterations or modifications not approved by the manufacturer.
• has safety devices which have been altered or disabled.
Failure to avoid these hazards could result in death or serious injury.
2.2 Component Identification
The following descriptions are for identification, explanation and locating purposes only.
Do not operate this aerial platform without proper authorization and training. Failure to avoid this hazard could result in death or serious injury. Before operating this aerial platform, perform the
following steps:
1. Visual and daily maintenance inspections (see Section 2.3)
2. Function tests (see Section 2.4)
3. Job site inspection It is the responsibility of the operator to perform a job site inspection and avoid
the following hazardous situations:
• holes or drop-offs
• ditches or soft fills
• floor obstructions, bumps or debris
• overhead obstructions
• electrical cords, hoses and high voltage conductors
• hazardous locations
• inadequate surface support to withstand all load forces imposed by the aerial platform
• wind and weather conditions
• the presence of unauthorized personnel
• other possible unsafe conditions
WARNING
An operator should not use any aerial platform that:
• does not appear to be working properly.
• has been damaged or appears to have worn or missing parts.
• has alterations or modifications not approved by the manufacturer.
• has safety devices which have been altered or disabled.
Failure to avoid these hazards could result in death or serious injury.
2.2 Component Identification
The following descriptions are for identification, explanation and locating purposes only.
----------مقدمة للشركة والموديل-------------
لكنترول يتكون من جزاين رايسيين هما 1..........2
لكنترول يتكون من جزاين رايسيين هما 1..........2
1.يتم شرح بيز كونترول وكيفيةاستخدامه للتشغيل
2.يتم شرح بلات فورم كونترول
وكيفية استخدامه للتشغيل
----------------------------------------
----------------------------------------
عمل مراجعة على انواع الكنترول وذكر سريع لكل من اجزائهما
((((((((((((((((انفو جرافيك))))))))))))))))))
Controlling Scissor Lifts
Through
Base Control---Platform Control
rise and low
select and hold (off-platform-base) key switch to the base position. Then select and hold (lower-neutral-raise) switch to either raise or lower position. Release switch to stop.
rise and low
select (lift-off-drive) switch to lift position, activate and hold enable trigger switch, Push controller joystick forward then the platform should rise to desired height. Pull controller joystick backward then the platform should lower.
drive
select (lift-off-drive) switch to drive position, activate and hold enable trigger switch, move controller joystick forward or backward to desired speed and direction of scissor lift travel.
Slowly push controller joystick in the forward direction then the scissor lift will start moving slowly. Full forward push for controller joystick makes the scissor lift go with its full speed.
Slowly pull controller joystick in the backward direction then the scissor lift will start moving slowly in reverse direction. Full backward pull for controller joystick makes the scissor lift move with its full speed.
steer
select (lift-off-drive) switch to drive position, activate and hold enable trigger switch,
Press rocker switch on top of controller joystick to right and steer wheels will turn right. Press rocker switch on top of controller joystick to left and steer wheels will turn left.
Note that driving and steering may be active at the same time.
No comments: